Module with biosensors BPM v1.2
(recognizing ECG / EMG / EEG signals)
out of stock
Module with biosensors BPM v1.2
(recognizing ECG / EMG / EEG signals)
out of stock
BPM v1.2 is a ready for use compact EMG/ECG/EEG module, designed for registration and measurement body biopotentials.
Very easy to use with such microcontrollers as Arduino, STM32 and Teensy. To receive a signal, it is enough to power the device with a voltage of 5V (no more than 5.5V) and connect the output signal to a ADC.
We provide free libraries for using BPM v1.2 with Arduino, Teensy and STM32, also we provide sketches for visualisation signals by Python and Matlab.
Features:
NOTE: this product is NOT a medical device and should not be used to diagnose or treat medical conditions.
Very easy to use with such microcontrollers as Arduino, STM32 and Teensy. To receive a signal, it is enough to power the device with a voltage of 5V (no more than 5.5V) and connect the output signal to a ADC.
We provide free libraries for using BPM v1.2 with Arduino, Teensy and STM32, also we provide sketches for visualisation signals by Python and Matlab.
Features:
- Operate voltage is 4.5 - 5.5 V. Typical 5.0 V.
- Low supply current 3 mA.
- Two analog output channels: OUT_3.3V in the range 0 - 3.3 V and OUT_5V in range 0 - 5 V.
- Base gain is 1000 V/V, can be increased by 8 additional Gain Selections: x1, x2, x4, x5, x8, x10, x16 or x32 V/V
- Serial Peripheral Interface (SPI) gain selection.
- 8 - 100 Hz filter.
- Dry skin contact.
- Stainless steel electrodes.
- Wire length ~ 50 cm
- Libraries for Arduino, STM32 and Teensy
- Examples of sketches for signal visualisation by Python and Matlab
NOTE: this product is NOT a medical device and should not be used to diagnose or treat medical conditions.
See the pdf-file below for more information on the features and connection of the module.
Datasheet BPM v1.2 (.pdf)
Datasheet BPM v1.2 (.pdf)
Interesting Related Articles and Reviews
- Article: "Electromyogram.What it is?"
- Article: "Overview the Elemyo-library for Arduino."
If you plan to use the module with a plugged-in PC (connected to the household power supply), we recommend purchasing a USB Isolator: it will reduce the interference caused by the household power supply and also make the connection safe.
BPM v1.2 is a ready for use compact EMG/ECG/EEG module, designed for registration and measurement body biopotentials.
Very easy to use with such microcontrollers as Arduino, STM32 and Teensy. To receive a signal, it is enough to power the device with a voltage of 5V (no more than 5.5V) and connect the output signal to a ADC.
We provide free libraries for using BPM v1.2 with Arduino, Teensy and STM32, also we provide sketches for visualisation signals by Python and Matlab.
Features:
NOTE: this product is NOT a medical device and should not be used to diagnose or treat medical conditions.
Very easy to use with such microcontrollers as Arduino, STM32 and Teensy. To receive a signal, it is enough to power the device with a voltage of 5V (no more than 5.5V) and connect the output signal to a ADC.
We provide free libraries for using BPM v1.2 with Arduino, Teensy and STM32, also we provide sketches for visualisation signals by Python and Matlab.
Features:
- Operate voltage is 4.5 - 5.5 V. Typical 5.0 V.
- Low supply current 3 mA.
- Two analog output channels: OUT_3.3V in the range 0 - 3.3 V and OUT_5V in range 0 - 5 V.
- Base gain is 1000 V/V, can be increased by 8 additional Gain Selections: x1, x2, x4, x5, x8, x10, x16 or x32 V/V
- Serial Peripheral Interface (SPI) gain selection.
- 8 - 100 Hz filter.
- Dry skin contact.
- Stainless steel electrodes.
- Wire length ~ 50 cm
- Libraries for Arduino, STM32 and Teensy
- Examples of sketches for signal visualisation by Python and Matlab
NOTE: this product is NOT a medical device and should not be used to diagnose or treat medical conditions.
Interesting Related Articles and Reviews
- Article: "Electromyogram.What it is?"
- Article: "Overview the Elemyo-library for Arduino."
